Safe underground blasting in coal mines, with the blasting vibrometer monitoring the impact of blasting on the surrounding environment!
1 Introduction
In mines with gas or coal dust explosion risks, mastering safe blasting techniques, understanding common knowledge of safe blasting, and complying with the Coal Mine Safety
Regulations, the Safe Operation Procedures and the Operating Regulations are of great significance for ensuring the safety of coal mine blasting operations, minimizing the blasting accident rate, and especially reducing or eliminating gas and coal dust explosion accidents caused by blasting in mines with gas or coal dust explosion risks.
2 One-Shot Three-Check System and Interlocked Blasting System
For blasting operations in gassy mines, the one-shot three-check system must be implemented on site. The one-shot three-check system means that gas must be checked on site before charging, before firing and after firing at the mining or excavation working face; when the gas concentration in the airflow within 20 m of the blasting location reaches 1%, charging and firing are prohibited. When the gas concentration reaches 1% after firing, it must be dealt with immediately, and drilling with electric drills is prohibited. Implementing the one-shot three-check system is a primary measure to strengthen gas checks before blasting, avoid missed checks, and prevent blasting under gas over-limit conditions.
The interlocked blasting system means that when the blaster enters the blasting working face, he first hands the exploder to the on-site team (group) leader; the team leader locks the exploder into the box for storing the exploder, the box key must be carried by the team leader at all times, and the exploder key must be carried by the blaster at all times. Before firing, gas is checked; the team leader is responsible for assigning people to guard, checking that guards are in place, checking roof support and the evacuation of personnel from the working face and counting heads; after confirming everything is correct, he takes out the exploder and hands it to the blaster, and the blaster gives the firing whistle and then fires. This process is supervised by the on-site safety officer or gas checker. The personnel implementing the interlocked blasting system are the team leader, safety officer and blaster in low-gassy mines and low-gas areas of high-gassy mines; in outburst-prone coal and gas mines, high-gassy mines and high-gas areas of low-gassy mines, they are the team leader, gas checker and blaster. Implementing the interlocked blasting system can prevent disorderly blasting operations, lax or unimplemented guarding that causes blasting injury accidents. Carefully checking the roof and support conditions before blasting can prevent roof fall accidents caused by blasting.
3 Reverse Initiation Operations
When millisecond blasting is used at mining and excavation working faces in high-gassy mines and high-gas areas of low-gassy mines, if reverse initiation is adopted, safety technical measures must be
formulated. The charge layout has a great influence on blasting effectiveness and blasting safety. From the perspective of the detonation propagation direction, the propagation direction of reverse charging points toward the blasthole mouth, and flame ejection from the blasthole mouth easily causes gas and coal dust explosions, so forward charging is considered safer than reverse charging. However, as long as stemming of sufficient length is filled in, the safety of reverse charging blasting will be greatly improved. From the perspective of blasting effectiveness, the propagation direction of reverse charging coincides with the rock movement direction, so reverse charging has better blasting results than forward charging. When millisecond blasting is used, from the perspective of causing the cut-off shot phenomenon, reverse charging blasting is safer than forward charging blasting.
Reverse initiation must meet the following requirements: ammonium nitrate explosives hardened to the point of not being kneadable by hand are prohibited, and emulsion explosives that have demulsified or hardened to the point of not being kneadable by hand are also prohibited; water-resistant explosives shall be used in wet or water-filled blastholes; placing booster charges at the hole bottom improperly is prohibited; the direction of the charge cartridge's cavity must be uniform, all facing the propagation direction toward the hole mouth; the detonator delay numbers must not be mixed up; charging is prohibited in collapsed, deformed, cracked or previously used blastholes; the use of high-safety water-containing explosives should be vigorously promoted.
4 Multi-Round Initiation Operations at Mining and Excavation Working Faces
At mining and excavation working faces with gas or coal dust explosion risks, millisecond blasting should be used. At excavation working faces, full-face single-shot initiation should be adopted; where full-face single-shot initiation cannot be achieved, safety measures must be adopted; at mining working faces, charges may be placed in groups, but each group of charges must be initiated at once.
Multi-round initiation at mining working faces must meet the following requirements: due to constraints of gas emission after blasting, roof management and coal output equipment capacity, where implementing group charging with single-shot initiation is indeed difficult at some mining working faces, one-time drilling, spaced group charging at one time, and group initiation may be used. The spacing between charged groups shall not be less than 2 m. To prevent uncharged blastholes in the spacing intervals from being squeezed and deformed during blasting, stemming sticks may be inserted into the blastholes; finally, depending on the grouping, the blastholes in the spacing intervals are charged with cartridges and blasted. When parallel operations are used at mining working faces, the distance between charging and drilling shall not be less than 5 m, the distance between charging and coal cutting shall not be less than 5 m, and charging and blasting are prohibited during roof caving time at the working face.
Multi-round initiation at excavation working faces must meet the following requirements: full-face charging with multi-round initiation is prohibited; drilling while charging is prohibited under any circumstances; if the blasthole leg wires are not long enough (the leg wires cannot extend out of the hole), the leg wires must be lengthened, the two leg wires connected in a staggered manner, and wrapped with adhesive tape; for each blasting, the minimum burden must comply with the regulations. At mining and excavation working faces with large gas emission, the quantity of single-shot blasting must be strictly controlled to avoid massive gas emission after blasting that causes gas accumulation over limits and leads to accidents.
5 Use of Water Stemming Cartridges
A water stemming cartridge is a filling material made by filling water into a tubular polyethylene plastic bag and sealing it. When the explosive in the blasthole detonates, the water in the water stemming cartridge absorbs a lot of heat, lowering the detonation temperature and shortening the duration of the blasting flame, thereby reducing the possibility of igniting gas or coal dust, which is conducive to coal mine production safety. The water curtain formed by water stemming cartridges can reduce dust and absorb toxic and harmful gases, improving the underground working environment.
When water stemming cartridges are used in underground blasting operations, the following requirements must be met: when the blasthole depth is <1.5 m, no fewer than 1 water stemming cartridge shall be used, and the clay stemming length outside the water cartridge shall not be <0.15 m; when the blasthole depth is >1.5 m, no fewer than 2 water stemming cartridges shall be used, and the clay stemming length outside the water cartridges shall not be <0.20 m.
6 Shallow-Hole Blasting Operations
When the blasthole depth is <0.6 m, charging and blasting are prohibited; under special conditions, such as floor lifting, side brushing and roof ripping where shallow-hole blasting is really needed, the blasthole depth may be <0.6 m, but safety measures must be formulated. The charge per hole for shallow-hole blasting shall not exceed 150 g; blastholes must be fully and firmly stemmed; before firing, water shall be sprayed for dust reduction and gas shall be checked within 20 m of the blasting location; when the gas concentration reaches 1%, charging and blasting are prohibited; before firing, inspect and reinforce the supports within 10 m of the blasting location; during blasting, guards must be properly arranged with a team leader directing on site; open-air blasting is prohibited.
7 Blasting Guards and Blasting Safety Isolation
Before blasting, the team leader must personally arrange dedicated personnel to serve as guards on the warning line and all passages that can enter the blasting location. Guards must stand guard at safe locations. Warning signs, railings or ropes shall be set at the warning line. The distance from the initiation location to the blasting location must be specified in detail in the operating regulations. Blasting guard requirements: all personnel evacuate beyond the warning line, with dedicated guards; the team leader is responsible for evacuation and guarding; all passages leading to the blasting location must be guarded, with the shot-firer responsible for one guard route; when two excavation working faces are 20 m apart before holing through and one fires, the other excavation working face must set guards; the warning line is blocked with ropes and signs are hung, with the words Blasting Now, No Entry written on the signs, implementing the three-guard principle of guard personnel, guard ropes and guard signs. Blasting safety distance (blasting firing line length): at mining working faces it shall not be <30 m; if there is rock parting or gangue at the mining working face, it shall not be <50 m. At coal seam roadway excavation working faces it shall not be <75 m; with one right-angle bend, it shall not be <50 m. At coal seam roadway uphill excavation working faces it shall not be <100 m; with one right-angle bend, it shall not be <75 m. At rock roadway and half-coal-rock roadway excavation working faces it shall not be <200 m, with shielding objects; with one right-angle bend, it shall not be <100 m. At rock roadway and half-coal-rock roadway uphill excavation working faces it shall not be <250 m, with shielding objects; with one right-angle bend, it shall not be <100 m.
8 Conclusion
Statistical analysis of 50 serious gas and coal dust explosion accidents nationwide shows that 17 were caused by violations in blasting operations, accounting for 34%. The experience of the vast majority of blasting accidents also shows that not mastering safe blasting techniques, lacking knowledge of coal mine safety production, ignoring safety production, not complying with various regulations, and working in violation of rules are the primary causes of coal mine safety accidents. Therefore, strengthening safety education and training and using blasting vibrometers, and improving the level of safe blasting techniques, are important measures to reduce coal mine safety accidents and ensure coal mine safety production.