Overview
During blasting, the release of explosive energy breaks the medium around the blastholes; at the same time, the action of blasting stress waves generates shear stress and tensile stress in distant media, causing cracks in the medium; a portion of the remaining energy propagates to the ground in the form of waves, causing ground particle vibration and forming blasting earthquakes. Both surface and underground engineering structures are affected by blasting earthquakes; during blasting engineering design, the blasting earthquake intensity needs to be checked according to actual conditions. In recent years, blasting demolition projects have been increasing; in order not to damage the buildings and equipment around the blasted body, strict control of blasting vibration is extremely important. Therefore, in controlled blasting design, blasting intensity checking is also needed. Usually theBlasting Vibration Meteris used to monitor the blasting vibration velocity.
Blasting Earthquakes and Natural Earthquakes
Blasting earthquakes and natural earthquakes are similar in that both release energy rapidly and propagate outward in the form of waves, causing particle vibration of the medium and producing earthquake effects. But blasting earthquakes also have the following characteristics:
1. The source energy of blasting earthquakes is small, and the affected range is small;
2. Short duration: blasting earthquakes generally last about 0.1 to 0.2 s, while natural earthquakes last long, generally about 10 to 40 s;
3. Blasting earthquake vibration frequency is high, while natural earthquakes are generally low-frequency vibrations;
4. The size and action direction of the blasting source can be controlled;
5. The vibration intensity can be adjusted by changing blasting techniques.
Although the two seismic wave parameters at the same location are the same, the influence and damage degree of blasting earthquakes on buildings there are lighter than natural earthquakes. Therefore, blasting earthquake problems should not be handled by the calculation methods for natural earthquakes.
Blasting Vibration Velocity
The ground vibration caused by blasting, like natural earthquakes, is a very complex random variable. It propagates in the form of waves, with amplitude, period and frequency all changing with time. The physical quantities of vibration are generally expressed by particle vibration velocity, acceleration, displacement and vibration frequency. Which physical quantities of vibration are used as criteria for measuring the intensity of blasting earthquake effects have different emphases in different engineering practices. At present, at home and abroad, the ground particle vibration velocity is mostly adopted as the criterion for measuring the intensity of blasting earthquake effects. This is because:
1. It can make the intensity of blasting vibration and natural earthquake intensity mutually referenced;
2. The currently used velocity sensors and secondary instruments are relatively common, and calibration and signal detection are relatively easy.
3. It is convenient to convert parameters related to structural damage criteria.
Calculation of Blasting Vibration Velocity
The vibration vector of rock media is obtained from the vector sum of three mutually perpendicular directions. Generally, vertical vibration velocity is used as the criterion. In theoretical derivation, since the magnitude of blasting vibration velocity is related to explosive quantity, distance, terrain, blasting methods, etc., many formulas (empirical formulas) have been derived; currently the most used is the result of similarity theory and dimensional analysis, giving a function relationship determined by the method of extrapolation in proportion to the cube root of the charge (the empirical formula proposed by Sadovsky). The software of the Zhongke Measurement and Control series of blasting vibrometers can all analyze blasting data for reference.
v = k (Q^(1/3)/R)^α Formula (1)
Where: V is the vibration velocity generated by blasting (cm/s); K is the medium coefficient; α is the attenuation coefficient; Q is the maximum per-delay charge (kg); R is the distance between the measuring point and the blast center (m). Since the geological conditions, charging design and other conditions of engineering blasting are ever-changing, the parameters in the formula often change; in particular, the values of the K and α coefficients must be determined under specific engineering conditions. Usually a small-charge test blast is used, and the measured data V, R, Q values are linearly regressed to calculate the values of a1 and a0: that is, transforming Formula (1) gives:
ln V = ln K + α ln(Q^(1/3)/R) Formula (2)
Let: y = ln V, a0 = ln K, a1 = α, x = ln(Q^(1/3)/R), giving:
y = a0 + a1 x Formula (3)
Find the values of K and α, then calculate the V value according to the designed Q and R values; at the same time, the V value should be made smaller than the safety vibration velocity [V] specified in the Safety Regulations for Blasting (GB 6722-86).
Safety vibration velocity: the vibration velocity of medium particles caused by blasting earthquakes, used as the criterion for measuring the intensity of blasting earthquake effects.
Different vibration velocities cause varying degrees of damage to roadways, buildings (structures), etc. To this end, China's Safety Regulations for Blasting (GB 6722-2014) stipulates the relevant safety vibration velocities to prevent hazards and losses caused by blasting vibration.
The safety vibration velocity for mine roadways is:
(1) Unstable surrounding rock but with good support: [V] < 10 cm/s. (2) Moderately stable surrounding rock with good support: [V] ≤ 20 cm/s. (3) Stable surrounding rock without support: [V] ≤ 30 cm/s.
The safety vibration velocity of ground particles for buildings (structures) is:
(1) Earthen cave dwellings, adobe houses, rubble stone houses: [V] ≤ 1 cm/s. (2) Ordinary brick buildings, non-aseismic large block buildings: [V] ≤ 2-3 cm/s. (3) Reinforced concrete frame buildings: [V] ≤ 5 cm/s.
Blasting Vibration Response Spectrum
As mentioned above, although the safety vibration velocity of blasting earthquakes has been adopted as the criterion for whether buildings (structures) are damaged, based on which to judge whether the building (structure) is safe under certain blasting conditions, the value of the blasting earthquake load that the building structure can withstand cannot yet be determined. Because the safety vibration velocity cannot determine the seismic load (seismic force) generated by explosive vibration on buildings (structures). Seismic load is different from general loads; general loads are independent of the dynamic characteristics of the structure and can be determined independently. Seismic load depends not only on the earthquake intensity, that is, the magnitude of influence and damage suffered during the earthquake, but is also closely related to factors such as the dynamic characteristics of the building, such as the natural vibration period and damping of the structure. At present, China and most countries in the world have adopted response spectrum theory in their seismic design codes for natural earthquakes to determine seismic loads.
The concept of the response spectrum: a damped harmonic vibrator (i.e., a single-degree-of-freedom system) is used to simulate a real building, and then the characteristics of this vibrator in withstanding the velocity, acceleration and displacement induced by the earthquake are examined. We take the measured ground acceleration curve as the input for determining the response spectrum; for a certain combination of natural frequency and damping, the maximum response to the ground acceleration is found, and this maximum response is a point on the response spectrum curve. Therefore, the response spectrum is defined as the relation curve of the maximum response (acceleration, velocity, displacement) of a single-degree-of-freedom system considering damping to a given ground acceleration versus the natural frequency (or period) of the system. The response spectrum calculation theory is based on the acceleration response spectrum curves drawn through analysis and calculation of measured records during earthquakes.
Application of response spectrum analysis in blasting earthquakes: blasting vibration waveforms can be intuitively analyzed, so why is response spectrum analysis still needed? Among the physical quantities of vibration intensity, such as the magnitude of amplitude and the duration of vibration, are easy to understand in the measured waveform. However, physical quantities such as the level and distribution of frequency and the magnitude of energy are not easy to obtain from the waveform diagram. Only through spectrum analysis can the frequency components and distribution ranges of each vibration parameter be obtained, and the frequency value of the dominant amplitude be obtained. Spectrum analysis of blasting earthquakes is very important; it provides indispensable vibration parameters for the dynamic analysis of various structures and underground works under blasting action.
Spectrum analysis: seismic waves are elastic waves in which particles vibrate periodically; the wave motion may be transient, periodic or random. In analyzing the action of earthquakes, what is of concern is the motion of particles generated as the earthquake passes. The basic equation of motion of harmonic vibration is:
u = u_max sin(wt) Formula (4)
Where: u is the particle displacement at time t; u_max is the displacement amplitude; w is the angular frequency, w = 2πf, f is the frequency. Differentiating Formula (4) gives the velocity (V) and acceleration (a) of the particle in harmonic vibration. If only the maximum value is considered, then in fact, the motion of particles in seismic waves is not simple harmonic vibration; the displacement amplitude and period are not fixed constants but change with time. But the relationship between the amplitudes of the above parameters can be used to analyze the motion of particles in seismic waves. The vibration waves generated by blasting contain waves of various components. Figure 1 is a relatively typical explosion seismogram. The three curves in the seismogram record the components of the particle position vector in three directions (longitudinal L, vertical Z, transverse T) respectively. It can be seen that body waves are recorded first, followed by surface waves. The frequency of the component with the largest amplitude among the harmonic components is the dominant frequency. The method for finding the dominant frequency is to perform Fourier spectrum analysis on the waveform; since the vibration waveform of the particle is a function of time, through Fourier transform, the function of the vibration waveform amplitude changing with time is transformed into a function of amplitude changing with frequency, that is, from the time domain to the frequency domain.
Spectrum analysis is based on Fourier series and Fourier integrals. Waveform analysis adopts the Fourier integral method, which is the relationship of transforming the signal x(t) in the time domain into the function x(w) in the frequency domain; the Fourier transform of x(t) exists only when the recorded waveform lasts for a duration T. Where: x(t) is the time history of the blasting vibration quantity (such as displacement, acceleration, etc.); x(w) is the spectrum of x(t); w is the angular frequency; j = -1 is the imaginary unit. The Fourier transform of a finite-length waveform is a complex number.
x(w) = R(w) + j I(w) Formula (5)
Where the real part is; the imaginary part is; the amplitude of the spectrum is; the phase spectrum is: the Fast Fourier Transform (i.e., the FFT algorithm) calculates the discrete Fourier transform (DFT) by separating the entire data sequence into several shorter sequences, replacing the DFT of the entire sequence. The FFT algorithm has various computational structure forms; the commonly used Cooley-Tukey method makes the sequence a 2^P data sequence. The FFT method can achieve faster speed and higher precision, achieving real-time analysis effects and replacing complicated calculations. Therefore, it is compiled into software for spectrum analysis on computers.
The block diagram of the measured blasting earthquake test system is shown in Figure 2. Using the above system, blasting earthquakes can be directly recorded, analyzed and printed to obtain the results of spectrum analysis and find the dominant frequency in the vibration waveform. The system can use a laptop computer to conduct tests directly on site. Finding the dominant frequency is used to judge the influence of seismic waves on the structure, analyze the response of the structure under seismic wave action, and calculate the magnitude and direction of the blasting seismic load.
Comprehensive Analysis
The intensity of blasting earthquake effects uses vibration velocity (or acceleration, displacement) as the criterion; to ensure the safety of buildings (structures), it must be controlled within the safety vibration velocity of the Safety Regulations for Blasting and relevant provisions. Domestically, velocity is mostly used as the basis for safety judgment, while Canada and the United States use acceleration as the safety judgment standard; each has advantages and disadvantages, selected according to one's own needs or testing convenience. To know the seismic load (seismic force) generated by blasting earthquakes, the dominant frequency must be found through testing and spectrum analysis. Seismic (blasting earthquake) design of certain buildings can be carried out, guiding blasting design and the safety measures taken, as well as post-accident analysis, etc. This is undoubtedly helpful for solving engineering blasting problems.
For more discussion on blasting vibrometers, blasting vibration sensors and blasting vibration velocity, please contact us at any time!