Technical Discussion

中文

Home/News/Technical NotesLayout, data, codes

Technical Notes

Practical notes on point layout, data processing and code interpretation.

4850N网络监测仪在桥梁振动监测方面的运用

Application of the 4850N network monitor in bridge vibration monitoring

With rapid economic development, health monitoring of bridges and large buildings is significant for normal operation and prevention of major public safety accidents.        Bridge safety monitoring systems monitor safety performance indicators of bridge spans, reflecting structural response under traffic loads and environment, analyzing health status and assessing

爆破测振仪xyz代表什么

What do X/Y/Z mean on a blasting vibration meter

What X/Y/Z mean on a blasting vibration meter - repeated tests obtain triaxial vibration velocity and dominant frequency

爆破测振仪怎么设置参数

How to set parameters on a blasting vibration meter

How to set parameters on the TC-4850: factory units come pre-configured and rarely need changes. Two ways: (1) via the bundled BVA analysis software (see software manual); (2) directly via the instrument keypad. Before testing, working parameters must be set for effective, accurate acquisition - sampling frequency, trigger level, trigger mode, record time, delay, etc. Note: no range setting needed - the system is self-adaptive

救援通道施工爆破对已建高铁隧道的振动安全分析

Vibration safety analysis of rescue-passage construction blasting on an existing high-speed railway tunnel

Abstract: To ensure the lining safety of the existing Jinshanding high-speed railway tunnel, blasting vibration monitoring was carried out during rescue-passage construction. TC-4850N wireless network vibration meters were used; results show the largest vibration on the facing side of the existing tunnel lining; least-squares regression yielded Sadovsky attenuation parameters, based on which vibration control measures were proposed - adjusting blasting parameters when velocity exceeds the safety threshold, with good results. Keywords: high

打桩、振冲、强夯振动监测的国家标准

National standards for piling, vibro-compaction and dynamic compaction vibration monitoring

Blasting vibration monitoring / existing tunnel vibration testing / piling and dynamic compaction monitoring. Piling, vibro-compaction and dynamic compaction cause repeated transient vibrations propagating as seismic waves from the excitation point - if uncontrolled, they may damage nearby buildings. Monitoring repeated transient vibrations during construction is necessary to protect structures. 1. Monitoring standard: per GB 50868-2013 Standard for Allowable Vibration of Building Engineering

爆破振动监测项目选择及爆破振动安全允许范围

Selection of blasting vibration monitoring items and safety allowable ranges

Selecting monitoring items - blasting vibration meters measure vibration velocity, acceleration and air shock wave    Blasting vibration monitoring includes velocity and acceleration measurement.     Velocity: the reciprocating speed of medium particles under seismic waves;     acceleration: the rate of change of that speed over time;    Item selection  &

超近距并行管沟精确爆破开挖的模拟分析

Simulation analysis of ultra-close parallel pipeline-trench precision blast excavation

     Abstract: To study the impact of ultra-close parallel pipeline-trench blast excavation on in-service pipelines, three schemes were simulated with ANSYS/LS-DYNA based on field tests. Results: in both tests and simulations, peak particle velocity of the pipeline in the y direction exceeds x and z; the y peak is largest at the ground surface, second on the facing side of the pipeline and smallest on the rear; under otherwise identical conditions, charge

减震孔微震爆破在地铁施工中的应用

Application of damping-hole micro-shake blasting in metro construction

Abstract: From three aspects - principle, design, safety measures and precautions of damping-hole micro-shake blasting in metro tunnel construction - the key points are described.   Keywords: damping-hole micro-shake blasting; buildings; safety. Text:   Take a Dalian metro contract section: design includes mined tunnel main body, pump house, civil-defense section and detour air ducts. Buildings above the section: distance from section roof top to pile bottoms is 3.7 m,

露天矿山爆破飞石的控制方法

Flyrock control methods for open-pit mine blasting

Abstract: Flyrock is one of the most serious potential accident factors in open-pit blasting and a main cause of damage to people, equipment and structures - a serious threat to life and property. Flyrock mechanisms are complex, involving both design and construction issues. This article analyzes causes and locations of flyrock, and proposes control measures via theoretical calculation of flight parameters - instructive for preventing flyrock accidents in open-pit mines and similar projects. Keywords: open-pit mine; blasting

爆破振动速度讨论-爆破测振仪

Discussion on blasting vibration velocity - blasting vibration meter

Overview     In blasting, explosive energy fragments the medium around blastholes, while stress waves induce shear and tensile stresses and cracks in distant media; part of the remaining energy propagates to the ground as waves, causing ground particle vibration - the blasting earthquake. Both surface and underground structures are affected; blast designs need seismic intensity checks per actual conditions. With demolition blasting increasing, to protect surrounding buildings and equipment